Parts
96 posts tagged Parts. Search within these →
Mamiya 645 Super/Pro: Gallery of Broken Mirror Stops
Gallery of broken Mamiya 645 Super/Pro mirror stops. An important word about this part: The mirror stop on the Mamiya 645 Super/Pro is made of a plastic…
RB67 Pro S 120 Back: Broken Release Plate Spring
Repairing a Mamiya RB67 120 ProS back. A bit of rust needed to be cleaned from some parts and the release plate spring was broken. To access the spring…
RZ67 Pro II 120 Back: Impact Damage and Dried Lubrication
Mamiya RZ67 Pro II 120 Back. Impact damage to the back and also some dried lubrication required disassembly to remove and clean the gear coupler (the part…
RZ67 Pro II: Straightening a Bent Focus Shaft
This RZ67II had impact damage to the left focus knob. The knob was slightly damaged (needed to be replaced) and the focus shaft was bent. The first video…
RB67 Pro S: Lens Stuck on Body After Impact Damage
This RB67 Pro S came into the shop with the complaint that the lens could not be removed. Body and lens working fine, but the lens lock ring would not…
Kodak Supermatic Shutter: Damaged Blades and Diaphragm Pivots
Repairing a Kodak Supermatic shutter. This particular shutter needed the usual cleaning to get the shutter to operate properly but also needed the blades…
Mamiya 645 Super: Shutter Service and Mirror Stop Replacement
Shutter service and mirror stop replacement on Mamiya 645 Super. This camera came into the shop with the shutter locked open and a broken mirror stop. It…
Mamiya NC1000S: Shutter and Meter Service, New Parts
Repairing this Mamiya NC1000s today. Needed a shutter/meter service in addition to replacing the front apron, bottom plate and battery cover. Fortunately I…
Seiko #0 Shutter: Rebuilding the Speeds Escapement
The speeds escapement that controls shutter speeds in the Seiko 0 shutters used in Mamiya C series TLR lenses and the Press series can develop issues such…
Minolta X-370: Light Baffle Replacement
Minolta X-370 Light Baffle Replacement. The first photo shows what happens when you try to insert a Minolta lens upside down (180 degrees off) on a Minolta…
RZ67: Shutter Not Fully Cocking, Broken Cocking Gear Assembly
Mamiya RZ67 repair. Symptom of this camera was that the shutter would cock but not completely and so the lens would appear to work on mechanical mode but…
RZ67 110mm f/2.8 Lens: Restaking a Broken Cocking Ring Pin
This Mamiya RZ67 110mm f/2.8 lens came into the shop locked up tight. Upon disassembly, I found that the locking pin for the rear cocking ring had broken…
Canon AE-1 Program: Bent Rewind Shaft and Cracked Bushing
This AE-1 Program came into the shop for a routine check/cleaning and I noticed that the rewind shaft was slightly bent. More than just a cosmetic issue as…
Mamiya C 80mm f/3.7 Lens: Replacing a Missing Sync Contact Assembly
This Mamiya 80mm f/3.7 lens came into the shop for routine shutter cleaning and I was advised that the customer had attempted a repair. What I was not told…
Mamiya 645 Super: Setting Mirror Angle After Stop Replacement
A broken mirror stop is a common repair on the Mamiya 645 Super, Pro and Pro TL. After replacing the stop, the mirror needs to be set to a 45 degree angle…
Mamiya 7: Winding Mechanism Repair, Broken Spring
Mamiya 7 winding mechanism repair. Third photo shows details of broken spring that needed replacing.
RB67 Shutters Removed for Parts
Removed RB67 shutters now used for parts.
Hasselblad Repair Parts
Hasselblad repair parts.
RB67 Pro SD: Replacing a Worn Winding Gear
Replacing worn winding gear Mamiya RB67 Pro SD.
RZ67 Pro II: Damaged Fine Focus Gear and New Replacement Gears
This Mamiya RZ67II came into the shop with a damaged fine focus gear, not an uncommon issue. Over the last few months, we have designed and fabricated new…
Kodak Carousel Projector: Solenoid Link and Focusing Gear Repair
A customer’s well worn kodak carousel projector that we brought back from the dead! Most of these you find today have a broken solenoid link and cracked…
Pentax K1000: Pegged Light Meter Needle, Faulty Galvanometer
A customer’s pentaxk1000 with a light meter needle that pegs up at all times. After a quick diagnosis the cause was found to be a faulty galvanometer…
Mamiya 35mm Cameras
Mamiya ended production of their 35mm camera line around 1983. If you are interested in having your Mamiya 35mm serviced, please contact me for details. If…
Repair Parts
I have a very large stock of parts for most Mamiya photographic products. Please contact me if you need parts for repair of your equipment.